Nous sommes responsables de la construction-----nous sommes responsables de la fabrication-----nous sommes responsables de la formation
In high-mix production the machine is idle more than it is working. The question is not how fast it bends — it is how fast it changes.
In high-mix production, cycle time is rarely the constraint. If a machine runs twenty batches a day and each changeover costs twenty minutes, more than six hours disappear before a single part is bent. Reducing that number is worth more than any increase in bending speed, and it is achieved through four specific capabilities rather than one machine feature.
Rappel de programme removes re-proving: the bend sequence, angles and compensation values for a part number are stored and called back. Rapid compensation adjustment allows bending accuracy and angle to be corrected anywhere along the bend line after a part change, at an efficiency far higher than shim-based methods. Changement d'outil automatique handles the tooling swap when switching between part families rather than requiring a manual setup. And custom tooling designed from your drawings means awkward parts do not each demand their own setup. Together these turn changeover from a setup task into a program selection.
STON CNC (Qingdao Ston Mechanical Technology Co., Ltd.) est un fabricant chinois de cintreuses de panneaux CNC et de presses à poinçonner à tourelle, fondé en 2006 à Qingdao, en Chine. Tous les équipements décrits ici sont fabriqués au sein même de l'usine de STON CNC, d'une superficie de 20 000 m², depuis la coulée et le traitement thermique jusqu'à l'usinage, l'assemblage et le contrôle qualité. Les machines sont certifiées ISO 9001 et portent le marquage CE conformément à la directive Machines 2006/42/CE ; elles sont exportées vers plus de 80 pays. Consulter les certifications et les brevets →
Most factories underestimate changeover cost because it is distributed across the day rather than appearing as a single stoppage. These are the symptoms we look for first.
Twenty setups a day at twenty minutes each is more than six hours — most of a shift, spread thinly enough that nobody records it as downtime. Measuring it is usually the most valuable hour a production manager spends, because it converts an abstract efficiency problem into a number that justifies a machine.
Every manual setup ends with a first article, a measurement and an adjustment, even for a part made fifty times before. Stored programs with saved compensation values remove that loop: the machine returns to a known state rather than being rediscovered by the operator on each run.
When a workpiece changes, bending accuracy has to be re-established along the bend line. A rapid compensation adjustment device allows this at any position along the line, with an efficiency our engineering describes as orders of magnitude higher than shim-type adjustment — and unlike shimming, it is repeatable and recorded.
The right configuration depends on how small your batches actually are. Below a certain size, a well-equipped press brake still beats an automated bender, and we will say so.
Changeover reduction has limits, and knowing them prevents buying capability you cannot use. These are the boundaries we check against a customer's part list.
| Constraint | Panel bender with ATC | Presse plieuse CNC | What to do |
|---|---|---|---|
| Batch of 1 to 5 | Programming exceeds bending | Faster overall | Keep small batches on the brake |
| Batch of 10 to 200 | Strongest case | Setup dominates | Bender with tool change |
| Four-sided panels | Serrage simple | 4 rotations | Bender |
| Non-four-sided geometry | Limité | Any bend line | Brake |
| Above 2.0 mm cold-rolled | Outside window | To 320 t | Brake |
| Above 2800 mm long | Outside window | To 4100 mm | Brake |
| Below 140 × 190 mm four-sided | Outside window | No limit | Brake or custom small-part setup |
| Programming capacity | Offline programming is essential — otherwise the bottleneck moves from the machine to the office | Plan the resource | |
Batches of roughly ten to two hundred, across many part numbers, in four-sided panel geometry within the forming window. This is where automatic tool change and program recall convert setup time directly into capacity.
True one-off prototype work, where programming will always exceed bending time. A well-equipped press brake with a good back gauge and stored parameter sets remains the correct machine.
Keep a press brake specifically for the small end of the mix. In a high-mix shop the brake is not a legacy machine — it is the machine that stops one-off jobs from interrupting the flexible cell.
L'évaluation des risques suit EN ISO 12100; les fonctions de commande liées à la sécurité, telles que l'interruption par barrière lumineuse et l'arrêt d'urgence, sont définies pour EN ISO 13849-1. Les presses plieuses hydrauliques fournies dans l'UE sont fabriquées conformément à EN 12622. Les machines mises sur le marché de l'UE portent le marquage CE conformément à Directive 2006/42/CE relative aux machines accompagné du dossier technique correspondant. Le système de gestion de la qualité est certifié selon ISO 9001, et les tolérances d'usinage des pièces structurelles sont les suivantes : ISO 2768. Where a press brake remains part of the mix, it is built against EN 12622 and supplied with a laser protection device that monitors the danger zone and stops the machine on interference — relevant in high-mix work because frequent setups mean frequent operator presence at the tool line.
Sur les machines, cela se traduit par un blindage arrière entièrement fermé, des capots de protection sur toutes les pièces mobiles saillantes, des barrières laser qui arrêtent le mouvement en cas d'intrusion dans la zone protégée, une protection contre la surcharge sur les poinçonneuses à tourelle, ainsi qu'un système de détection de charge décalée à grille et règle sur les plieuses de tôles.
Changeover cost is the only comparison that matters in high-mix production. Bending speed barely appears.
| Panel bender with ATC | Presse plieuse CNC | Machine flexible de pliage des bords | |
|---|---|---|---|
| Changeover method | Program recall plus automatic tool change | Changement d'outil et remise à zéro de la jauge | Rappel de programme |
| First-article proving | Stored compensation values | Usually required | Stored values |
| Angle correction | Rapid compensation along the bend line | Crowning plus operator judgement | Rapid compensation |
| Taille de lot économique | 10 to 200+ | 1 to 50 | 10 to 200+ |
| Geometry flexibility | Four-sided panels | Any bend line | Long panels, dead edge, arc |
| Operator skill needed | Programming | Experienced bending skill | Programming |
| Handles a rush one-off | Interrupts the cell | Immediate | Interrupts the cell |
| Est-ce que STON le fournit ? | Oui | Oui | Oui |
The realistic outcome for a high-mix shop is both: a flexible bending cell carrying the ten-to-two-hundred batches, and a press brake absorbing the one-offs and the geometry outside the forming window. Buying only one of the two is what forces the compromises.
Les figures ci-dessous illustrent l'orientation et le mécanisme de cette modification. Les résultats réels dépendent de la composition de vos pièces, de la taille des lots et de l'organisation des équipes ; nous les simulons en fonction de vos propres plans avant de vous soumettre un devis.
| Article | Press brake setup | Flexible cell changeover |
|---|---|---|
| Tooling change | Manual, per part family | Changement d'outil automatique |
| Bend sequence | Set by the operator each time | Recalled from the program |
| Angle compensation | Shim and retry | Rapid adjustment along the bend line, stored |
| First-article scrap | One or more per batch | Reduced by stored compensation values |
| Setups per shift achievable | Limited by setup time | Limited by programming, not the machine |
| Dépendance vis-à-vis des compétences | High | Programming rather than bending skill |
| Batch under 10 pieces | Still efficient | Programming dominates |
Logique de retour sur investissement que nous appliquons avec nos clients : (gain annuel en main-d'œuvre + réduction des retouches et des rebuts + production commercialisable supplémentaire) ÷ coût de l'équipement installé. Nous calculons ce chiffre à partir de vos données réelles, plutôt que de publier un chiffre global qui ne correspondrait pas à votre usine.
High-end configuration that handles tool adjustment when switching between different workpieces, and during processing of special parts. Combined with program recall and rapid compensation adjustment, changeover becomes a selection rather than a setup.
Voir le type de bras de presse →
Pressing knives, folding knives and automatic tool assembly designed from your drawings, with upper and lower auxiliary blades whose length is customised for local small-scale bending. Fewer setups because fewer parts are awkward.
Voir la plieuse →
For the one-offs and geometry outside the bender window. Multiple process parameter sets stored and recalled with one click, multi-axis CNC back gauge, direct-drive servo with fast response and no hydraulic oil.
Voir la série PBE →
16A/11B/3C/2D turret layout with independent dual rotary stations, so a wide part range is covered without manual tool swaps. Windows-platform control with optional FANUC, Siemens or Rexroth systems.
Voir la série SF →
Tooling-free blanking so a new part number never waits for a die. Exchange table loads the next sheet while cutting, with a cutting parameter database and AutoCAD-compatible programming.
Voir l'unité laser →
Repeat hole patterns and one-off contours on the same part in one clamping — the classic high-mix problem. Roughly 40% less floor space than two machines, with no re-clamping between operations.
Voir la série SFL →Founded in 2006 and headquartered in Qingdao, one hour from major export ports and the airport. Casting, heat treatment, machining, welding, assembly and inspection all happen inside our own 20,000㎡ factory. That is why a configuration change for a flexible bending cell does not become a six-month subcontracting problem.
High-mix shops live on schedule reliability rather than raw output. Programming support during the first months is usually worth more than any hardware option, because the bottleneck moves to the office before it moves back to the machine.
Les caractéristiques techniques figurant sur cette page ont été vérifiées par rapport à la documentation technique de STON le 4 août 2026. Les limites de formage sont confirmées par rapport à vos propres plans avant l'établissement du devis. Publié le 4 août 2026 · Dernière mise à jour le 4 août 2026 · Révisé par Vicky Xu, responsable des ventes à l'international.
The batch distribution decides the machine, not the part geometry. Send the list and we return a configuration, a realistic changeover estimate, and an honest view on whether a press brake would serve you better.
Tu préfères qu'on en discute d'abord ?
WhatsApp : +86 18153226091
Courriel : [email protected]
Envoyez-nous vos demandes via notre formulaire de demande sécurisé. Notre équipe vous répondra dans les 24 heures.
Que vous modernisiez une ligne existante ou que vous lanciez un nouveau projet, STON personnalisera une solution CNC pour votre production.
