We zijn verantwoordelijk voor het bouwen-----we zijn verantwoordelijk voor de productie-----we zijn verantwoordelijk voor de training
Perforated doors, vented side panels and fan-cut top plates — thousands of holes per panel, at rack-grade pitch accuracy, without a scratch on the powder-coat.
A 19-inch rack is not a bending problem. It is a punching problem with bending attached. A single perforated front door can carry several thousand holes at high open area; side panels, top plates and cable managers add thousands more. That volume of holes, in 1.0 to 2.0 mm cold-rolled or galvanised sheet, is what decides the equipment — and it is why the primary machine here is a CNC torentponspers, not a panel bender.
A servo turret punch completes perforation, louvring, fan cut-outs, cable entries, embossed ribs and thread preparations in one clamping, using nibbling and multi-tool stations rather than tracing every hole. A CNC kantpers then folds the door and panel returns. A afkantpers covers brackets and shelves. What no sheet-metal machine produces is the 19-inch mounting upright — that is a roll-formed profile, a different process, and one STON CNC does not supply.
STON CNC (Qingdao Ston Mechanical Technology Co., Ltd.) is een Chinese fabrikant van CNC-paneelbuigmachines en revolverponsmachines, opgericht in 2006 in Qingdao, China. Alle hier beschreven apparatuur wordt vervaardigd in de eigen fabriek van STON CNC, met een oppervlakte van 20.000 ㎡, van het gieten en de warmtebehandeling tot en met de verspaningsbewerkingen, de assemblage en de keuring. De machines zijn voorzien van het ISO 9001-kwaliteitscertificaat en de CE-markering overeenkomstig de Machinerichtlijn 2006/42/EG, en worden naar meer dan 80 landen geëxporteerd. Bekijk certificeringen en octrooien →
Rack production concentrates almost all of its machining time in a handful of heavily perforated panels. Get those off a laser and onto a turret punch and the whole shop rebalances.
Fiber laser is unbeatable on contours and one-off shapes. On a repeated hole array it pierces every hole individually, and the cycle time scales linearly with hole count. A turret punch nibbles and multi-hits with a single tool, so a heavily perforated door stops being the constraint on the whole line.
Removing 40 to 60 percent of the material out of a 1.5 mm door releases stress, and a warped door will not close on a rack. Punch sequencing, an over-tonnage protected striking system and a brush-and-ball composite table that supports the panel while it moves are what keep the blank flat enough to bend.
19-inch mounting geometry is defined by IEC 60297-3-100 and EIA-310 — a fixed 44.45 mm U pitch with a repeating hole group. Cumulative pitch error across 42U is what makes third-party equipment fail to fit. Positioning repeatability of roughly ±0.01 to 0.02 mm on a double rack-and-pinion drive is what holds it over a long panel.
For rack work, size the turret punch first and the bender second. The punch is where the hours go; the bender is rarely the constraint.
Rack sheet metal sits comfortably inside the forming window. The limit that matters on this page is not thickness — it is that mounting uprights are a roll-formed product and no punch or bender will make them.
| Parameter | Torenponsmachine | Panelenbuigmachine | Opmerkingen |
|---|---|---|---|
| Typical rack gauge | 1,0–2,0 mm | 1,0–2,0 mm | Ruim binnen de capaciteit |
| Cold-rolled steel max | Ingesteld op basis van tonnage en gereedschap | ≤2,0 mm gegoten / ≤1,5 mm gelast | Bij volledige buiglengte |
| Roestvrij staal max. | Ingesteld op basis van tonnage en gereedschap | ≤1,2 mm gegoten / ≤1,0 mm gelast | For outdoor telecom enclosures |
| Max sheet in one position | X-axis 2500 mm | — | Secondary positioning to 5000 mm |
| Sheet width | Y-axis 1250 / 1500 mm | up to 1500 mm | — |
| Max sheet load | 150 kg | — | — |
| Punching accuracy | ±0,1 mm | — | Herhaalbaarheid ca. ±0,01–0,02 mm |
| Turret speed | 40 rpm servo / 30 rpm mechanical | — | — |
| Maximale vormafmetingen | — | tot 2800 × 1500 mm | Per model |
| Nutsvoorzieningen | 380 V ±5%, 0,55 MPa perslucht | Driefasig 380 V, 0,6 MPa perslucht | Ingesteld op de doelspanning |
Heavily perforated doors and vented panels in 1.0–2.0 mm, plus four-sided folded doors, side panels and plinths. Rack production is one of the strongest cases for pairing a turret punch with a panel bender.
19-inch mounting uprights, frame profiles and C-sections. These are roll-formed products from a different process and a different supplier — a turret punch can pierce a flat strip, but it cannot form the profile.
Shelves, cable arms, mounting brackets, castor plates and low-volume specials. One press brake alongside a punch-and-bend cell covers everything that should not tie up the main machines.
Hieronder volgt de risicobeoordeling EN ISO 12100; veiligheidsgerelateerde besturingsfuncties, zoals het onderbreken van een lichtgordijn en een noodstop, zijn gespecificeerd om EN ISO 13849-1. Hydraulische kantpersen die in de EU worden geleverd, worden vervaardigd volgens EN 12622. Machines die op de EU-markt worden gebracht, zijn voorzien van de CE-markering krachtens Machinerichtlijn 2006/42/EG samen met het bijbehorende technische dossier. Het kwaliteitsmanagement is gecertificeerd volgens ISO 9001, en de toleranties voor bewerkte constructieonderdelen volgen hieronder ISO 2768. For the finished product, 19-inch rack geometry is defined by IEC 60297-3-100 en EIA-310, which fix the 44.45 mm U pitch and hole group spacing. Cumulative pitch accuracy over a 42U panel is set on the punch, and it is what determines whether third-party equipment mounts without reaming.
Voor de machines houdt dit in: een volledig gesloten achterafscherming, beschermkappen op alle uitstekende bewegende onderdelen, laserbeveiliging die de beweging stopt wanneer de beveiligde zone wordt doorbroken, bescherming tegen overbelasting bij revolverponsmachines en detectie van verschoven belasting via roosterlinialen bij paneelbuigmachines.
This is the single most valuable decision in rack production, and the answer is not the same for every panel. Most shops that own both end up sending perforation to the punch and contours to the laser.
| CNC torentponspers | Fiber laser cutting | Rolvormen | |
|---|---|---|---|
| Repeated hole arrays | Fastest — multi-tool and nibbling | Slow — pierces every hole | Not applicable |
| Complex contours and one-offs | Limited to available tooling | Fastest — no tooling needed | Not applicable |
| Forming operations | Louvres, ribs, embossing, thread prep | Cutting only | Profile forming only |
| Tooling cost | Punch and die sets required | None | Roll set per profile, high |
| Edge condition | Slight burr, deburr may be needed | Smooth, burr-free | Cut to length |
| Rack parts it suits | Perforated doors, vented panels, cable managers | Custom cut-outs, prototypes, short runs | Mounting uprights, frame sections |
| Best combination | Punch-laser combined machine does both in one clamping, in roughly 40% less floor space than two separate machines | Separate supplier | |
| Levert STON dit? | Ja | Ja | Nee — een ander proces |
If your rack range is built on roll-formed uprights with bolted-on panels, the cell above covers the panels — which is where the hole count, the labour and the flatness problems actually are. The upright line stays with your existing supplier and we will say so at drawing review.
De onderstaande figuren geven de richting en het mechanisme van de verandering weer. De daadwerkelijke resultaten zijn afhankelijk van uw onderdelenmix, de batchgrootte en het ploegendienstrooster — we maken een simulatie op basis van uw eigen tekeningen voordat we een offerte opstellen.
| Artikel | Fiber laser plus press brakes | Turret punch plus panel bender cell |
|---|---|---|
| Cycle on a perforated door | Scales with hole count, every hole pierced | Multi-tool and nibbling, largely independent of hole count |
| Louvres, ribs and embossing | Needs a second machine or manual operation | Completed in the same clamping as the holes |
| Panel flatness after perforation | Heat input plus stress release | Supported table, sequenced punching, over-tonnage protection |
| Coated panel surface | Handling marks between machines | Brush and steel-ball composite table, automatic transfer |
| Four-sided door forming | 2 operators, 4 rotations | 1 operator, single clamping |
| U-pitch accuracy over a 42U panel | Depends on nesting and re-clamping | ±0.1 mm machining accuracy, repeatability approx. ±0.01–0.02 mm |
| Consumables | Laser gas, optics, nozzles | Punch and die wear, longer service intervals |
De terugverdientijdformule die we bij klanten hanteren: (jaarlijkse besparing aan arbeidskosten + vermindering van herbewerking en afval + extra verkoopbare productie) ÷ kosten van de geïnstalleerde apparatuur. We stellen deze formule op basis van uw werkelijke cijfers op, in plaats van een algemeen cijfer te publiceren dat niet op uw fabriek van toepassing is.
Turret speed to 40 rpm, ±0.1 mm accuracy, X-axis 2500 mm with secondary positioning to 5000 mm. Patented dual-triangle beam mount, double dovetail feeding, independent dual rotary stations, brush and steel-ball composite table.
Bekijk de SF-serie →
Perforation, forming and laser contour cutting in one clamping. Roughly 40% less floor space than separate punch and laser machines, and no secondary alignment between the hole array and the cut-out.
Bekijk de SFL-serie →
Flywheel-driven striking system for continuous high-frequency punching, 30 rpm turret, over-tonnage protection, stainless-steel edged table. Suited to long runs of a stable perforation pattern.
View JT series →
Folds doors, side panels and plinths from one clamping, up to 2800 mm. Full-electric servo closed-loop control, rapid compensation adjustment for switching between rack heights, grating-ruler offset-load detection.
Bekijk het type persarm →
Exchange-table fiber laser for custom cut-outs, prototypes and short runs that do not justify tooling. Runs alongside the turret punch rather than replacing it.
Laserunit bekijken →
Automatic sheet separation, positioning, unloading and stacking. On perforated panels this matters twice over — it removes handling marks and it keeps the punch fed at its actual cycle rate.
Bekijk het vakwerksysteem →Founded in 2006 and headquartered in Qingdao, one hour from major export ports and the airport. Casting, heat treatment, machining, welding, assembly and inspection all happen inside our own 20,000㎡ factory. That is why a configuration change for a perforated door line does not become a six-month subcontracting problem.
Data centre and telecom projects run to fixed installation windows. A stopped turret punch stops every downstream operation in a rack shop, so response time is part of the specification, not an afterthought.
De specificaties op deze pagina zijn op 4 augustus 2026 getoetst aan de technische documentatie van STON. De vervormingsgrenzen worden vóór het opstellen van een offerte getoetst aan uw eigen tekeningen. Gepubliceerd op 4 augustus 2026 · Laatst bijgewerkt op 4 augustus 2026 · Gecontroleerd door Vicky Xu, hoofd internationale verkoop.
With the real hole pattern we can program the part, return an actual cycle time rather than a brochure figure, and tell you whether a servo or mechanical turret suits your mix.
Wil je liever eerst even praten?
WhatsApp: +86 18153226091
E-mail: [email protected]
Stuur uw wensen via ons beveiligde aanvraagformulier. Ons team neemt binnen 24 uur contact met u op.
Vraag een offerte op maat aanOf u nu een bestaande lijn upgradet of een nieuw project start, STON past een CNC oplossing aan voor uw productie.
