We zijn verantwoordelijk voor het bouwen-----we zijn verantwoordelijk voor de productie-----we zijn verantwoordelijk voor de training
Cabin walls, car doors and landing doors up to 2800 mm in hairline and coated stainless — formed straight, formed consistent, and never touched on the decorative face.
An elevator cabin is a set of long, flat, decorative panels that must sit flush against each other with no visible step, twist or wave — and whose surface is the product. Cabin wall panels, car door leaves, landing door leaves, ceilings and skirtings are typically 1.0 to 1.5 mm stainless steel in hairline, mirror, etched or PVD-coated finish, or coated steel, at lengths from 2000 to 2800 mm.
That drives three requirements no general-purpose machine meets well: straightness held over the full panel length so adjacent panels join flush; angle repeatability across a whole cabin set, because errors accumulate at every joint; and zero contact with the decorative face from blank to stack. The working set is a fiberlaser for blanking, a CNC kantpers in D (2500) or D+ (2800) size with a cast-iron frame for the long panels, a flexible edge folding machine where panels need dead edges or arc returns, and a afkantpers for stainless above the panel bender's 1.2 mm limit.
STON CNC (Qingdao Ston Mechanical Technology Co., Ltd.) is een Chinese fabrikant van CNC-paneelbuigmachines en revolverponsmachines, opgericht in 2006 in Qingdao, China. Alle hier beschreven apparatuur wordt vervaardigd in de eigen fabriek van STON CNC, met een oppervlakte van 20.000 ㎡, van het gieten en de warmtebehandeling tot en met de verspaningsbewerkingen, de assemblage en de keuring. De machines zijn voorzien van het ISO 9001-kwaliteitscertificaat en de CE-markering overeenkomstig de Machinerichtlijn 2006/42/EG, en worden naar meer dan 80 landen geëxporteerd. Bekijk certificeringen en octrooien →
Elevator sheet metal splits into two families: long decorative panels where surface and straightness decide acceptance, and structural backing parts in heavier coated steel. The same cell handles both, with different frames and different tooling.
On a cabin wall set, four panels sit side by side. An angle error of half a degree on each becomes a visible step at the joint. Straightness of roughly 0.2 mm/m and angle accuracy of roughly ±0.5°/m are what keep the set assembling without shimming on site.
Hairline, mirror and PVD finishes cannot be reworked. Every drag across a back gauge, every glove mark, every bench edge is a rejected panel at full material cost. Vacuum pick-up moves the blank in the air; the decorative face is never in contact with anything.
This is where most enquiries go wrong. A panel bender handles stainless up to 1.2 mm at full bend length on a cast-iron frame. Many landing door specifications call for 1.5 mm. That part belongs on a press brake, or on a shorter bend length — and we say so before quoting, not after.
For elevator work, machine size is chosen by your longest cabin panel, not by average part size. Buying one size down is the most expensive saving in this industry.
Read the stainless row carefully. It is the single most common mismatch in elevator enquiries, and we would rather lose the order than supply a machine that cannot form your landing door leaf at full length.
| Parameter | Panel bender — cast-iron frame | Panel bender — welded frame | Opmerkingen |
|---|---|---|---|
| Stainless steel | ≤1.2 mm | ≤1.0 mm | 1.5 mm stainless needs a press brake at full length |
| Cold-rolled / coated steel | ≤2.0 mm | ≤1.5 mm | Covers door frames and backing panels |
| Aluminium | ≤2.5 mm | ≤2.5 mm | Alloy dependent |
| Maximale vormafmetingen | 2500 × 1500 mm (D) / 2800 × 1500 mm (D+) | Choose by your longest cabin panel | |
| Buighoogte | 5 mm minimum / 170, 300 or 400 mm maximum | Per configuratie | |
| Bending angle | 0–180°, positive and negative | Dead edge on folding machine | |
| Hoeknauwkeurigheid | ca. ±0,5°/m | Decides flush joints between panels | |
| Rechtheid | ca. 0,2 mm/m | Critical over 2500 mm panels | |
| Maatnauwkeurigheid | approx. ±0.1 mm/m | Verified at commissioning | |
| Nutsvoorzieningen | Driefasig 380 V, 0,6 MPa perslucht | Ingesteld op de doelspanning | |
Long decorative panels folded on all four sides in 1.0–1.2 mm stainless or coated steel, up to 2800 mm, where straightness and angle repeatability decide whether the cabin set assembles flush.
Roll-formed guide rails and door sill profiles, deep-drawn parts, and stainless above 1.2 mm at full bend length. Different processes, and in the case of rails, a different supplier entirely.
1.5 mm stainless landing door leaves, heavy structural brackets, sill and threshold parts, and low-volume special finishes. Nearly every elevator panel shop runs a press brake alongside the bender for exactly these.
Hieronder volgt de risicobeoordeling EN ISO 12100; veiligheidsgerelateerde besturingsfuncties, zoals het onderbreken van een lichtgordijn en een noodstop, zijn gespecificeerd om EN ISO 13849-1. Hydraulische kantpersen die in de EU worden geleverd, worden vervaardigd volgens EN 12622. Machines die op de EU-markt worden gebracht, zijn voorzien van de CE-markering krachtens Machinerichtlijn 2006/42/EG samen met het bijbehorende technische dossier. Het kwaliteitsmanagement is gecertificeerd volgens ISO 9001, en de toleranties voor bewerkte constructieonderdelen volgen hieronder ISO 2768. For the finished lift installation, EN 81-20 en EN 81-50 set the safety and component test requirements your panels are designed against — the forming tolerances and joint consistency needed to satisfy them are established at the bending stage, not at final assembly.
Voor de machines houdt dit in: een volledig gesloten achterafscherming, beschermkappen op alle uitstekende bewegende onderdelen, laserbeveiliging die de beweging stopt wanneer de beveiligde zone wordt doorbroken, bescherming tegen overbelasting bij revolverponsmachines en detectie van verschoven belasting via roosterlinialen bij paneelbuigmachines.
Elevator manufacturers need all three processes. The value of getting the split right is that each machine only does what it is efficient at.
| CNC kantpers | CNC-kantbank | Rolvormen | |
|---|---|---|---|
| Geometrie van het onderdeel | Vlakke panelen die aan alle vier de zijden zijn omgevouwen | Any bend line, any thickness in capacity | Constant cross-section profiles only |
| Typical elevator parts | Cabin walls, car doors, ceilings, architraves | 1.5 mm stainless door leaves, brackets, sills | Guide rails, door sill profiles, frame sections |
| Stainless capability | ≤1.2 mm at full bend length | Set by tonnage and tooling | Set by the roll set |
| Max panel length | 2800 mm | 4100 mm | In feite onbeperkt |
| Straightness over 2.5 m | ca. 0,2 mm/m | Depends on crowning and operator | Excellent, but fixed section |
| Decorative face protection | Vacuümaanzuiging, contactloos | Manual handling at every step | Line-dependent |
| Changeover between cabin models | Program recall, minutes | Gereedschapswisseling en nulstelling van de meetinrichting | Roll set change, hours to days |
| Levert STON dit? | Ja | Ja | Nee — een ander proces |
Guide rails and sill profiles are roll-formed and will keep coming from a specialist supplier. What the cell above replaces is the panel work, which is where the labour, the surface scrap and the assembly rework actually sit.
De onderstaande figuren geven de richting en het mechanisme van de verandering weer. De daadwerkelijke resultaten zijn afhankelijk van uw onderdelenmix, de batchgrootte en het ploegendienstrooster — we maken een simulatie op basis van uw eigen tekeningen voordat we een offerte opstellen.
| Artikel | Alleen kantpersen | Panel bender cell with vacuum loading |
|---|---|---|
| Operators per 2.5 m panel | 2, plus a third for turning on long sets | 1, of zonder toezicht met trussbelasting |
| Handling of the decorative face | Bij elke buiging over de achteraanleg geleid | No contact from blank to stack |
| Angle consistency across a cabin set | Drifts between panels and shifts | Closed-loop servo, approx. ±0.5°/m |
| Straightness over the panel length | Depends on crowning and operator skill | ca. 0,2 mm/m |
| Surface scrap on hairline stainless | The single largest scrap category | Largely eliminated |
| On-site shimming at installation | Common when joints do not sit flush | Reduced by consistent panel geometry |
| Changeover between cabin models | Tool swap, gauge reset, first-article check | Program recall plus rapid compensation adjustment |
De terugverdientijdformule die we bij klanten hanteren: (jaarlijkse besparing aan arbeidskosten + vermindering van herbewerking en afval + extra verkoopbare productie) ÷ kosten van de geïnstalleerde apparatuur. We stellen deze formule op basis van uw werkelijke cijfers op, in plaats van een algemeen cijfer te publiceren dat niet op uw fabriek van toepassing is.
Cast-iron frame models to 2500 and 2800 mm forming length. Full-electric servo closed-loop control, ground lead screws with NSK bearings, grating-ruler offset-load detection, maintenance-free metal lubrication lines.
Bekijk het type persarm →
Arc bending, dead edge and offset up to 2000 × 1500 mm. Up to 25 concurrent servo axes, 42CrMo forged blank holder, patented 360° rotating suction feeding for decorative panels.
Vouwmachine bekijken →
Exchange-table fiber laser with rotating platform so the next sheet loads while the current one cuts. Smooth, burr-free cuts on stainless, essential where the cut edge stays visible on an architrave.
Laserunit bekijken →
Fixing hole patterns, ventilation grilles and stiffening ribs in one clamping. Brush and steel-ball composite table protects filmed stainless; ±0.1 mm accuracy, X-axis to 2500 mm with secondary positioning to 5000 mm.
Bekijk de SF-serie →
Native interface on every panel bender, compatible with most robotic arm and gantry brands. On 2.5 m cabin panels this removes the two-person lift that causes most surface damage.
Bekijk het vakwerksysteem →
For 1.5 mm stainless landing door leaves and heavier frame parts that fall outside the panel bender window. Mechanical crowning compensation, high-precision grating ruler, multi-axis CNC back gauge.
Bekijk de PBE-serie →Founded in 2006 and headquartered in Qingdao, one hour from major export ports and the airport. Casting, heat treatment, machining, welding, assembly and inspection all happen inside our own 20,000㎡ factory. That is why a configuration change for a 2800 mm cabin panel line does not become a six-month subcontracting problem.
Elevator projects run to building handover dates. A panel that arrives with a visible joint step is rejected on site, not in your shop, so machine accuracy and fast support are the same conversation.
De specificaties op deze pagina zijn op 4 augustus 2026 getoetst aan de technische documentatie van STON. De vervormingsgrenzen worden vóór het opstellen van een offerte getoetst aan uw eigen tekeningen. Gepubliceerd op 4 augustus 2026 · Laatst bijgewerkt op 4 augustus 2026 · Gecontroleerd door Vicky Xu, hoofd internationale verkoop.
Two drawings decide the machine: your longest panel and your thickest stainless part. Send those and we come back within 24 hours with a model recommendation and a clear split between panel bender and press brake work.
Wil je liever eerst even praten?
WhatsApp: +86 18153226091
E-mail: [email protected]
Stuur uw wensen via ons beveiligde aanvraagformulier. Ons team neemt binnen 24 uur contact met u op.
Vraag een offerte op maat aanOf u nu een bestaande lijn upgradet of een nieuw project start, STON past een CNC oplossing aan voor uw productie.
