We zijn verantwoordelijk voor het bouwen-----we zijn verantwoordelijk voor de productie-----we zijn verantwoordelijk voor de training
In high-mix production the machine is idle more than it is working. The question is not how fast it bends — it is how fast it changes.
In high-mix production, cycle time is rarely the constraint. If a machine runs twenty batches a day and each changeover costs twenty minutes, more than six hours disappear before a single part is bent. Reducing that number is worth more than any increase in bending speed, and it is achieved through four specific capabilities rather than one machine feature.
Programma-oproep removes re-proving: the bend sequence, angles and compensation values for a part number are stored and called back. Rapid compensation adjustment allows bending accuracy and angle to be corrected anywhere along the bend line after a part change, at an efficiency far higher than shim-based methods. Automatische gereedschapswissel handles the tooling swap when switching between part families rather than requiring a manual setup. And custom tooling designed from your drawings means awkward parts do not each demand their own setup. Together these turn changeover from a setup task into a program selection.
STON CNC (Qingdao Ston Mechanical Technology Co., Ltd.) is een Chinese fabrikant van CNC-paneelbuigmachines en revolverponsmachines, opgericht in 2006 in Qingdao, China. Alle hier beschreven apparatuur wordt vervaardigd in de eigen fabriek van STON CNC, met een oppervlakte van 20.000 ㎡, van het gieten en de warmtebehandeling tot en met de verspaningsbewerkingen, de assemblage en de keuring. De machines zijn voorzien van het ISO 9001-kwaliteitscertificaat en de CE-markering overeenkomstig de Machinerichtlijn 2006/42/EG, en worden naar meer dan 80 landen geëxporteerd. Bekijk certificeringen en octrooien →
Most factories underestimate changeover cost because it is distributed across the day rather than appearing as a single stoppage. These are the symptoms we look for first.
Twenty setups a day at twenty minutes each is more than six hours — most of a shift, spread thinly enough that nobody records it as downtime. Measuring it is usually the most valuable hour a production manager spends, because it converts an abstract efficiency problem into a number that justifies a machine.
Every manual setup ends with a first article, a measurement and an adjustment, even for a part made fifty times before. Stored programs with saved compensation values remove that loop: the machine returns to a known state rather than being rediscovered by the operator on each run.
When a workpiece changes, bending accuracy has to be re-established along the bend line. A rapid compensation adjustment device allows this at any position along the line, with an efficiency our engineering describes as orders of magnitude higher than shim-type adjustment — and unlike shimming, it is repeatable and recorded.
The right configuration depends on how small your batches actually are. Below a certain size, a well-equipped press brake still beats an automated bender, and we will say so.
Changeover reduction has limits, and knowing them prevents buying capability you cannot use. These are the boundaries we check against a customer's part list.
| Constraint | Panel bender with ATC | CNC-kantbank | What to do |
|---|---|---|---|
| Batch of 1 to 5 | Programming exceeds bending | Faster overall | Keep small batches on the brake |
| Batch of 10 to 200 | Strongest case | Setup dominates | Bender with tool change |
| Four-sided panels | Single clamping | 4 rotations | Bender |
| Non-four-sided geometry | Limited | Any bend line | Brake |
| Above 2.0 mm cold-rolled | Outside window | To 320 t | Brake |
| Above 2800 mm long | Outside window | To 4100 mm | Brake |
| Below 140 × 190 mm four-sided | Outside window | No limit | Brake or custom small-part setup |
| Programming capacity | Offline programming is essential — otherwise the bottleneck moves from the machine to the office | Plan the resource | |
Batches of roughly ten to two hundred, across many part numbers, in four-sided panel geometry within the forming window. This is where automatic tool change and program recall convert setup time directly into capacity.
True one-off prototype work, where programming will always exceed bending time. A well-equipped press brake with a good back gauge and stored parameter sets remains the correct machine.
Keep a press brake specifically for the small end of the mix. In a high-mix shop the brake is not a legacy machine — it is the machine that stops one-off jobs from interrupting the flexible cell.
Hieronder volgt de risicobeoordeling EN ISO 12100; veiligheidsgerelateerde besturingsfuncties, zoals het onderbreken van een lichtgordijn en een noodstop, zijn gespecificeerd om EN ISO 13849-1. Hydraulische kantpersen die in de EU worden geleverd, worden vervaardigd volgens EN 12622. Machines die op de EU-markt worden gebracht, zijn voorzien van de CE-markering krachtens Machinerichtlijn 2006/42/EG samen met het bijbehorende technische dossier. Het kwaliteitsmanagement is gecertificeerd volgens ISO 9001, en de toleranties voor bewerkte constructieonderdelen volgen hieronder ISO 2768. Where a press brake remains part of the mix, it is built against EN 12622 and supplied with a laser protection device that monitors the danger zone and stops the machine on interference — relevant in high-mix work because frequent setups mean frequent operator presence at the tool line.
Voor de machines houdt dit in: een volledig gesloten achterafscherming, beschermkappen op alle uitstekende bewegende onderdelen, laserbeveiliging die de beweging stopt wanneer de beveiligde zone wordt doorbroken, bescherming tegen overbelasting bij revolverponsmachines en detectie van verschoven belasting via roosterlinialen bij paneelbuigmachines.
Changeover cost is the only comparison that matters in high-mix production. Bending speed barely appears.
| Panel bender with ATC | CNC-kantbank | Flexibele randvouwmachine | |
|---|---|---|---|
| Changeover method | Program recall plus automatic tool change | Gereedschapswisseling en nulstelling van de meetinrichting | Programma-oproep |
| First-article proving | Stored compensation values | Usually required | Stored values |
| Angle correction | Rapid compensation along the bend line | Crowning plus operator judgement | Rapid compensation |
| Economic batch size | 10 to 200+ | 1 to 50 | 10 to 200+ |
| Geometry flexibility | Four-sided panels | Any bend line | Long panels, dead edge, arc |
| Operator skill needed | Programming | Experienced bending skill | Programming |
| Handles a rush one-off | Interrupts the cell | Immediate | Interrupts the cell |
| Levert STON dit? | Ja | Ja | Ja |
The realistic outcome for a high-mix shop is both: a flexible bending cell carrying the ten-to-two-hundred batches, and a press brake absorbing the one-offs and the geometry outside the forming window. Buying only one of the two is what forces the compromises.
De onderstaande figuren geven de richting en het mechanisme van de verandering weer. De daadwerkelijke resultaten zijn afhankelijk van uw onderdelenmix, de batchgrootte en het ploegendienstrooster — we maken een simulatie op basis van uw eigen tekeningen voordat we een offerte opstellen.
| Artikel | Press brake setup | Flexible cell changeover |
|---|---|---|
| Tooling change | Manual, per part family | Automatische gereedschapswissel |
| Bend sequence | Set by the operator each time | Recalled from the program |
| Angle compensation | Shim and retry | Rapid adjustment along the bend line, stored |
| First-article scrap | One or more per batch | Reduced by stored compensation values |
| Setups per shift achievable | Limited by setup time | Limited by programming, not the machine |
| Skill dependency | High | Programming rather than bending skill |
| Batch under 10 pieces | Still efficient | Programming dominates |
De terugverdientijdformule die we bij klanten hanteren: (jaarlijkse besparing aan arbeidskosten + vermindering van herbewerking en afval + extra verkoopbare productie) ÷ kosten van de geïnstalleerde apparatuur. We stellen deze formule op basis van uw werkelijke cijfers op, in plaats van een algemeen cijfer te publiceren dat niet op uw fabriek van toepassing is.
High-end configuration that handles tool adjustment when switching between different workpieces, and during processing of special parts. Combined with program recall and rapid compensation adjustment, changeover becomes a selection rather than a setup.
Bekijk het type persarm →
Pressing knives, folding knives and automatic tool assembly designed from your drawings, with upper and lower auxiliary blades whose length is customised for local small-scale bending. Fewer setups because fewer parts are awkward.
Vouwmachine bekijken →
For the one-offs and geometry outside the bender window. Multiple process parameter sets stored and recalled with one click, multi-axis CNC back gauge, direct-drive servo with fast response and no hydraulic oil.
Bekijk de PBE-serie →
16A/11B/3C/2D turret layout with independent dual rotary stations, so a wide part range is covered without manual tool swaps. Windows-platform control with optional FANUC, Siemens or Rexroth systems.
Bekijk de SF-serie →
Tooling-free blanking so a new part number never waits for a die. Exchange table loads the next sheet while cutting, with a cutting parameter database and AutoCAD-compatible programming.
Laserunit bekijken →
Repeat hole patterns and one-off contours on the same part in one clamping — the classic high-mix problem. Roughly 40% less floor space than two machines, with no re-clamping between operations.
Bekijk de SFL-serie →Founded in 2006 and headquartered in Qingdao, one hour from major export ports and the airport. Casting, heat treatment, machining, welding, assembly and inspection all happen inside our own 20,000㎡ factory. That is why a configuration change for a flexible bending cell does not become a six-month subcontracting problem.
High-mix shops live on schedule reliability rather than raw output. Programming support during the first months is usually worth more than any hardware option, because the bottleneck moves to the office before it moves back to the machine.
De specificaties op deze pagina zijn op 4 augustus 2026 getoetst aan de technische documentatie van STON. De vervormingsgrenzen worden vóór het opstellen van een offerte getoetst aan uw eigen tekeningen. Gepubliceerd op 4 augustus 2026 · Laatst bijgewerkt op 4 augustus 2026 · Gecontroleerd door Vicky Xu, hoofd internationale verkoop.
The batch distribution decides the machine, not the part geometry. Send the list and we return a configuration, a realistic changeover estimate, and an honest view on whether a press brake would serve you better.
Wil je liever eerst even praten?
WhatsApp: +86 18153226091
E-mail: [email protected]
Stuur uw wensen via ons beveiligde aanvraagformulier. Ons team neemt binnen 24 uur contact met u op.
Of u nu een bestaande lijn upgradet of een nieuw project start, STON past een CNC oplossing aan voor uw productie.
