{"id":8688,"date":"2026-08-24T09:26:15","date_gmt":"2026-08-24T01:26:15","guid":{"rendered":"https:\/\/stoncncmachine.com\/?post_type=news&p=8688"},"modified":"2026-08-24T09:26:15","modified_gmt":"2026-08-24T01:26:15","slug":"vergelijking-van-verschillende-soorten-cnc-laad-en-losrobotsystemen","status":"publish","type":"news","link":"https:\/\/stoncncmachine.com\/nl\/news\/cnc-loading-and-unloading-robot-system-types-compared\/","title":{"rendered":"CNC-robotsystemen voor laden en lossen: een vergelijking van de verschillende typen"},"content":{"rendered":"

A CNC loading and unloading robot system<\/strong><\/a> moves blanks and finished panels between a stack and a forming machine without an operator lifting them. Three types dominate sheet metal work: articulated robotic arms, gantry loaders, and truss-type manipulators. Choose by panel size, floor space, and surface finish risk, not by robot brand.<\/p>\n

What the term actually covers<\/h2>\n

Afor sheet metal is a handling device plus its end effector, its stack or destack station, its safety enclosure, and the software handshake with the processing machine. The handling device is only one line item of four. Buyers who compare quotations on robot payload alone usually find the price difference sitting in the other three.
\nThree mechanical architectures are in common use:
\nArticulated robotic arm.<\/strong> A multi-joint arm mounted on a floor pedestal or a short linear track, reaching into the machine from the side or the front. Motion is free-form, so one arm can serve a bender, a stacking pallet, and a rework table from the same base.<\/p>\n

Gantry loader.<\/strong> A bridge structure spanning the machine, with a vertical Z-axis carrying the pick head. Motion is Cartesian: X, Y, Z, sometimes a rotation. It works above the machine rather than beside it.
\nTruss-type manipulator.<\/strong> A rail-mounted carriage running along an overhead beam, usually spanning several metres and serving one or more machines in a line. Structurally it is a stretched gantry, and in practice suppliers use the two words interchangeably. The distinction that matters is span: a gantry is usually built around a single machine envelope, a truss runs down a process line.
\nSTON supplies robotic-arm and truss configurations as standard product lines, and the panel bender and flanging platforms retain a native docking interface that accepts robotic arms and gantry loaders from most manufacturers on the market. That interface point is worth checking on any machine you already own, because retrofitting one is an order of magnitude more expensive than specifying it.<\/p>\n

\"Arm(1)<\/p>\n

The three types side by side<\/h2>\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Selection Dimension<\/th>\nArticulated Robotic Arm<\/th>\nGantry Loader<\/th>\nTruss Manipulator<\/th>\n<\/tr>\n<\/thead>\n
Floor Space Added<\/strong><\/td>\nPedestal footprint plus swept safety envelope beside the machine<\/td>\nMinimal added floor area; occupies the volume above the machine<\/td>\nRail length runs the whole cell; supports land at fixed pier points<\/td>\n<\/tr>\n
Ceiling Height Needed<\/strong><\/td>\nLow<\/td>\nModerate to high<\/td>\nHigh, plus a clear overhead run<\/td>\n<\/tr>\n
Panel Size Handled<\/strong><\/td>\nLimited by reach and by moment arm at full extension<\/td>\nSet by beam span and head design<\/td>\nLongest panels of the three, set by rail length<\/td>\n<\/tr>\n
Motion Type<\/strong><\/td>\nFree-form, multi-position<\/td>\nLinear, repeatable<\/td>\nLinear along a line of machines<\/td>\n<\/tr>\n
Serves Multiple Machines<\/strong><\/td>\nTwo, sometimes three within one reach circle<\/td>\nNormally one<\/td>\nSeveral in sequence<\/td>\n<\/tr>\n
Changeover Flexibility<\/strong><\/td>\nHighest; new part path is a program change<\/td>\nMedium; may need head or fixture change<\/td>\nMedium<\/td>\n<\/tr>\n
Surface Damage Exposure<\/strong><\/td>\nGripper contact points and swing clearance<\/td>\nSuction pick, mostly vertical motion<\/td>\nSuction pick over long transfers<\/td>\n<\/tr>\n
Typical Fit<\/strong><\/td>\nMixed-model work, short runs, awkward part shapes<\/td>\nSingle high-volume machine, tight floor plan<\/td>\nCutting-to-bending line, long panels<\/td>\n<\/tr>\n
Main Weakness<\/strong><\/td>\nReach circle is fixed once the pedestal is anchored<\/td>\nRebuilding the cell layout later is costly<\/td>\nLong un<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Most published comparisons of CNC handling automation<\/strong> come from the machine-tool-tending world, where the part is a chuck-sized billet and the deciding factor is payload. Sheet metal inverts that. A 1.0 mm cold-rolled blank at 1200 \u00d7 650 mm weighs about 6 kg but has an area of 0.78 m\u00b2 and almost no bending stiffness. The problems are flatness during transfer, double-sheet pickup, and surface marking, not lifting force. Read payload-led comparisons with that in mind.<\/p>\n

\"Laser<\/p>\n

Footprint: budget the safety envelope, not the machine<\/h2>\n

The number that ruins layouts is not the robot’s own footprint. It is the fenced area around it.
\nSTON kantpersen<\/strong> <\/a>in the press-arm series give an indication of the base machine envelope: the A (1000) welded model measures 425 \u00d7 160 \u00d7 255 cm, and the B (1400) cast-bed model 450 \u00d7 206 \u00d7 290 cm. Those are machine dimensions with no handling equipment attached.
\nA comparable jump shows up in the laser cutting range, where the same 3015 format is offered in single-table and exchange-table builds. The single-table machine occupies roughly 4500 \u00d7 2600 mm. The exchange-table version occupies roughly 9000 \u00d7 3100 mm. Same cutting area, 2.4 times the floor space, because material handling has been designed into the machine rather than bolted beside it.<\/p>\n

Apply the same arithmetic to your own cell:<\/p>\n

    \n
  1. Draw the base machine envelope from the technical drawing, not the brochure.<\/li>\n
  2. Add the destack pallet position and the finished-part stack position. Two pallet stations at 1500 \u00d7 1200 mm each is a reasonable planning figure for cabinet panel work.<\/li>\n
  3. Add the handling device: for an arm, its pedestal plus full swing radius; for a gantry or truss, the pier positions and the rail overrun at each end.<\/li>\n
  4. Add the fenced safety perimeter and at least one gate wide enough for a pallet truck.<\/li>\n
  5. Add operator access on the control-panel side and maintenance access to the hydraulic or pneumatic group.<\/li>\n
  6. Check clear height under any existing crane rail, duct run, or roof truss before committing to an overhead type.<\/li>\n<\/ol>\n

    \"Drie<\/p>\n

    Automation shrinks your maximum panel size<\/h2>\n

    This is the section most equipment pages leave out, and it changes purchasing decisions more than any throughput claim.
    \nAdding automatic loading and unloading to a forming machine reduces the largest part the machine can produce. The gripper or suction head needs clearance inside the forming area, and the transfer path needs room that the manual operator did not need. STON’s flexible edge bending (flanging) machines publish both figures, which makes the effect measurable:<\/p>\n\n\n\n\n\n\n\n
    Model<\/th>\nMax Forming Dimension, Manual (mm)<\/th>\nMax Forming Inner Dimension with Automatic Loading\/Unloading (mm)<\/th>\nReduction in the Second Dimension<\/th>\n<\/tr>\n<\/thead>\n
    1200<\/td>\n1200 \u00d7 1200<\/td>\n1200 \u00d7 650<\/td>\n\u221246%<\/td>\n<\/tr>\n
    1600<\/td>\n1600 \u00d7 1250<\/td>\n1600 \u00d7 950<\/td>\n\u221224%<\/td>\n<\/tr>\n
    2000<\/td>\n2000 \u00d7 1500<\/td>\n2000 \u00d7 800<\/td>\n\u221247%<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

    Across all three models the length axis is unaffected and the width axis carries the whole loss. Minimum four-sided inner dimension stays at 200 \u00d7 200 mm and minimum bending height at 4 mm in both configurations, so the small-part end of the range is unchanged.
    \nTwo consequences follow. First, if your largest running panel is close to the manual limit, automation may simply exclude that part number, and you will be running it manually on the same machine anyway. Second, the reduction is not proportional across the range, so a model that looks like the obvious size step up may give you less automated width than the model below it. Take your five highest-volume panel sizes, lay them against the automated column rather than the headline column, and check the fit before choosing a machine size.<\/p>\n

    A common misconception is that this limit is a software setting that can be relaxed after installation. It is mechanical. The clearance belongs to the pick head and the transfer path, and changing it means changing hardware.<\/p>\n

    Where surface damage comes from<\/h2>\n

    Scratched panels are the most frequent complaint after an automation retrofit in cabinet, kitchen equipment, and appliance-panel plants, where the material arrives pre-galvanised or as stainless with a protective film. Three mechanisms account for most of it.
    \nContact during pickup. STON flanging machines<\/strong> <\/a>use a patented suction-cup feeding method with 360\u00b0 free rotation, which spreads the holding load over the pad area instead of concentrating it at gripper jaws. Suction is generally kinder to a finished face than mechanical clamping, but it demands a flat, clean, dry blank; oil residue or a curled leading edge causes drop events, and a dropped panel is a scrapped panel.
    \nSliding contact on the machine table. The turret punch press platform<\/strong> uses a brush and omnidirectional steel-ball composite tabletop, customisable to pure bristle brush or pure steel ball, with a stainless steel edged countertop. That choice is not cosmetic. Steel balls roll well under heavier sheets but can leave point marks on soft or coated material; full brush is gentler and slower. Specify the tabletop against your worst-case surface requirement, not your average one.<\/p>\n

    Stacking at the unload end. Panels stacked without spacing rub against each other under their own weight during pallet transport. Interleaving or programmed spacing at the stacking station is an option on most systems and is cheap to add at order stage.
    \nWhere the surface specification is critical, ask for a sample run with your own material and your own protective film before signing off. Film behaviour under suction varies by supplier and by ambient temperature, and no specification sheet will tell you how yours performs.<\/p>\n

    \"Flensmachine\"<\/p>\n

     <\/p>\n

    Site and interface requirements to confirm before ordering<\/h2>\n\n\n\n\n\n\n\n\n\n
    Artikel<\/th>\nSTON Published Requirement<\/th>\nWaarom het belangrijk is<\/th>\n<\/tr>\n<\/thead>\n
    Machine Handling Interface<\/td>\nNative docking port on panel bender and flanging platforms; accepts most robotic arm and gantry brands<\/td>\nDetermines whether integration is configuration or custom engineering<\/td>\n<\/tr>\n
    Air Supply<\/td>\n0.6 MPa at panel benders; 0.55 MPa at turret punch presses; 0.5\u20130.6 MPa and 0.6 m\u00b3\/min on production lines<\/td>\nSuction pickup fails intermittently on marginal air, and intermittent faults are the hardest to diagnose<\/td>\n<\/tr>\n
    Stroomvoorziening<\/td>\nThree-phase 380 V \u00b15% at machine level; 3\u03c6 400 V \u00b15%, 50 Hz \u00b12% quoted for line configurations<\/td>\nAffects transformer sizing at the cell<\/td>\n<\/tr>\n
    Machine Table Load<\/td>\n150 kg maximum load capacity on the turret punch press table<\/td>\nCaps stack weight staged on the machine<\/td>\n<\/tr>\n
    Guarding<\/td>\nProtective covers on protruding parts; fully enclosed rear enclosure on flanging machines<\/td>\nBaseline for the risk assessment, not a substitute for it<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

    For equipment entering the EU, the handling cell is assessed as an assembly of machinery. Risk assessment follows EN ISO 12100, safety-related control functions are rated to EN ISO 13849-1, and press-type forming equipment in the cell falls under EN 12622 or EN ISO 16092 depending on the machine. Compliance is against Machinery Directive 2006\/42\/EC, transitioning to Regulation (EU) 2023\/1230. Confirm at order stage who carries responsibility for the conformity assessment of the combined cell: the machine builder, the integrator, or you. On retrofits to an existing machine, it is frequently the end user, and that surprise arrives late.<\/p>\n

    FAQ<\/h2>\n

    Q: What is the difference between an unloading robot and an unloading machine?<\/h3>\n

    A: An unloading robot is a programmable arm with free-form motion. An unloading machine usually means a mechanical device with fixed or linear motion, such as a gantry loader, truss manipulator, or stacker. The robot is programmed for a new part; the machine is often reconfigured for one.<\/p>\n

    Q: Can a loading system be added to a panel bender I already own?<\/h3>\n

    A: If the machine has a native handling docking port, yes, and the work is mostly configuration. STON panel benders and flanging machines retain that interface as standard. Without one, expect custom mechanical and control engineering that can cost as much as the handling unit.<\/p>\n

    Q: How much does a CNC loading and unloading robot system cost?<\/h3>\n

    A: STON does not publish list prices for handling systems, because the figure depends on the handling type, the end effector, the number of stack stations, the guarding, and the machine it integrates with. Request a quotation with your panel dimensions, material, thickness, stack height, and target takt time, and ask for the layout drawing alongside the price so you can verify the footprint.<\/p>\n

    Q: Will automation handle my full sheet size?<\/h3>\n

    A: Not necessarily. On the flanging machines the automated forming envelope is narrower than the manual one, by 24% to 47% on the width axis depending on model. Check your largest panel against the automated figure specifically.<\/p>\n

    Q: Which type is best for a mixed-model cabinet plant?<\/h3>\n

    A: An articulated arm, in most cases, because reprogramming a path is cheaper than changing a pick head. Once panels pass about 2 m, the calculation moves toward a gantry or truss even with a mixed product range.<\/p>\n

    Q: How long does operator training take?<\/h3>\n

    A: STON provides training through video tutorials, manuals, and on-site sessions, with 24\/7 technical support and a 48-hour on-site response commitment. Plan for the sequence programming to be the part your team needs longest, not the daily operation.<\/p>\n

     <\/p>","protected":false},"excerpt":{"rendered":"

    A CNC loading and unloading robot system moves blanks and finished panels between a stack and a forming machine without an operator lifting them. Three types dominate sheet metal work: articulated robotic arms, gantry loaders, and truss-type manipulators. Choose by panel size, floor space, and surface finish risk, not by robot brand. What the term […]<\/p>\n","protected":false},"featured_media":0,"comment_status":"open","ping_status":"closed","template":"","class_list":["post-8688","news","type-news","status-publish","hentry","news_category-industry-news"],"acf":[],"_links":{"self":[{"href":"https:\/\/stoncncmachine.com\/nl\/wp-json\/wp\/v2\/news\/8688","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/stoncncmachine.com\/nl\/wp-json\/wp\/v2\/news"}],"about":[{"href":"https:\/\/stoncncmachine.com\/nl\/wp-json\/wp\/v2\/types\/news"}],"replies":[{"embeddable":true,"href":"https:\/\/stoncncmachine.com\/nl\/wp-json\/wp\/v2\/comments?post=8688"}],"wp:attachment":[{"href":"https:\/\/stoncncmachine.com\/nl\/wp-json\/wp\/v2\/media?parent=8688"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}