{"id":7891,"date":"2026-08-05T13:38:48","date_gmt":"2026-08-05T05:38:48","guid":{"rendered":"https:\/\/stoncncmachine.com\/?post_type=news&p=7891"},"modified":"2026-08-05T13:40:09","modified_gmt":"2026-08-05T05:40:09","slug":"panel-bending-machine-vs-press-brake-how-to-choose","status":"publish","type":"news","link":"https:\/\/stoncncmachine.com\/fr\/news\/panel-bending-machine-vs-press-brake-how-to-choose\/","title":{"rendered":"Machine \u00e0 plier les panneaux ou presse plieuse : comment faire son choix ?"},"content":{"rendered":"

Choose a cintreuse de panneaux<\/strong> when one part carries many short flanges and the sheet stays inside the machine’s thickness range: on STON<\/a>‘s press-arm series that means cold-rolled steel up to 2.0 mm and stainless up to 1.2 mm on a cast-iron bed. Choose a press brake when thickness, tonnage or unpredictable geometry drives the job.<\/p>\n

\"STON<\/p>\n

The difference is not speed. It is who moves.<\/h2>\n

On a press brake, the part moves and the tool stays. An operator lifts the blank, positions it against the back gauge, steps on the pedal, rotates the part, repeats. Four flanges on a cabinet door means four handling cycles, and on a 2.5 m panel it means two people doing them in sync.
\nOn a panel bender, the part is clamped once by a blank holder and the bending blades move around it. Up bends and down bends happen without turning the sheet over. That single mechanical fact drives almost every downstream difference: labour per part, consistency between the first piece and the five-hundredth, scratch risk on pre-coated stainless, and the amount of floor space needed for handling rather than forming.<\/p>\n

Everything else follows from it. So does every limitation.<\/p>\n

Side-by-side: the dimensions that actually change a purchase decision<\/h2>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Decision Dimension<\/th>\nCintreuse de panneaux CNC<\/a> (STON Press-Arm Series)<\/th>\nCNC Press Brake (STON PBS \/ PBE)<\/th>\n<\/tr>\n<\/thead>\n
Forming Principle<\/td>\nBlank holder clamps once; bending blades form each edge<\/td>\nPunch descends into a V-die, completing one bend per stroke<\/td>\n<\/tr>\n
Handling per Part<\/td>\nOne load and one unload<\/td>\nOne handling cycle per bend line<\/td>\n<\/tr>\n
Max. Thickness at Full Bend<\/td>\nWelded bed: CR 1.5 mm \/ SS 1.0 mmCast bed: CR 2.0 mm \/ SS 1.2 mm<\/td>\nDetermined by tonnage: 63\u2013320 t across the published range<\/td>\n<\/tr>\n
Max. Working Length<\/td>\n1000\u20132800 mm, depending on the model<\/td>\n1500\u20134100 mm, depending on the model<\/td>\n<\/tr>\n
Bend Height Range<\/td>\nMinimum: 5 mmMaximum options: 170 \/ 300 \/ 400 mm<\/td>\nLimited by tooling and open height rather than machine geometry<\/td>\n<\/tr>\n
Minimum Four-Sided Inner Dimension<\/td>\n140 \u00d7 190 mm<\/td>\nNo equivalent constraint<\/td>\n<\/tr>\n
Angle Range<\/td>\n0\u2013180\u00b0<\/td>\nDetermined by tooling<\/td>\n<\/tr>\n
Published Angle Accuracy<\/td>\nApprox. \u00b10.5\u00b0\/m<\/td>\nClosed-loop grating scale with mechanical crowning compensation<\/td>\n<\/tr>\n
Published Dimensional Accuracy<\/td>\nApprox. \u00b10.1 mm\/mStraightness: approx. 0.2 mm\/m<\/td>\nDepends on tooling, back-gauge programming, and the operator<\/td>\n<\/tr>\n
Changeover Between Parts<\/td>\nProgram recall; 15 servo axes reposition automatically<\/td>\nTool change and back-gauge reprogramming<\/td>\n<\/tr>\n
Operator Skill Dependency<\/td>\nLow after training<\/td>\nHigh and remains operator-dependent<\/td>\n<\/tr>\n
Machine Weight<\/td>\nLighter structure with a larger footprint<\/td>\n4,500 kg for 63\/1500 model to 19,000 kg for 320\/4100 model<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Where a panel bender is the wrong buy<\/h2>\n

Most machine-builder content on this topic argues one direction and stops. Compared with the general-purpose bending packages usually quoted against a cintreuse de panneaux<\/strong>, the panel bender genuinely does win on enclosure-type work \u2014 and there are four situations where recommending one would be wrong.<\/p>\n

    \n
  1. Your thickest regular part exceeds the bed’s rating. A welded-frame press-arm machine stops at 1.5 mm cold-rolled and 1.0 mm stainless. Moving to a cast-iron bed lifts that to 2.0 mm and 1.2 mm. If your product mix includes 3 mm mounting plates or 4 mm structural brackets, no panel bender configuration covers them. That job belongs on a 100 t or 150 t press brake, and buying a panel bender first means buying a press brake anyway six months later.<\/li>\n
  2. Your parts are smaller than the clamp can hold. Four-sided forming needs an inner dimension of at least 140 \u00d7 190 mm. Small junction boxes, terminal covers and switch plates fall under it. Two-sided forming relaxes this to roughly 140 mm, which helps, but not enough for genuinely small components.<\/li>\n
  3. Your flange is shorter than 5 mm or taller than the blade travel. Minimum bend height is 5 mm. Maximum is 170, 300 or 400 mm depending on configuration selected at order time \u2014 and that is chosen once, at purchase. A part with a 450 mm return wall will not fit a machine specified with 400 mm blades, and retrofitting is not a field operation.<\/li>\n
  4. \u00a0Your batch structure is genuinely one-off. A panel bender pays back through repeat. Job shops running fifty different drawings a week with a median batch of three pieces spend their day programming rather than forming. The press brake, with its 400 mm\/s class servo back gauge and single-click recall of stored programs on a DELEM 53T\/58T\/66T\/69T control, handles that mix with less setup overhead per drawing.<\/li>\n<\/ol>\n

    \"STON<\/p>\n

    The misconception worth correcting<\/h3>\n

    Plants upgrading from manual bending often frame this as replacement. In practice almost nobody scraps their press brakes when a panel bender arrives. The press brake keeps the prototypes, the repair parts, the thick brackets, the odd trapezoid nobody drew properly, and the remake when a customer changes a flange three days before shipment. What changes is the ratio: the panel bender absorbs the repeating 70\u201380% of enclosure volume, and the press brake stops being the bottleneck for everything else.<\/p>\n

    Budget for both. Sequence them by which one is currently constraining output.<\/p>\n

    What the STON A2\u2013F2 numbers allow<\/h2>\n

    The press-arm series runs from A (1000 \u00d7 1000 mm forming size) through A+ (1200), B (1400 \u00d7 1250), B+ (1600 \u00d7 1250), C (2000 \u00d7 1500), D (2500 \u00d7 1500) to D+ (2800 \u00d7 1500). Every model in the standard configuration carries 15 servo axes.
    \nBed construction is the specification that changes the answer more than model size does:<\/p>\n

      \n
    1. Welded steel bed<\/strong> (available across A through D+): CR 1.5 mm \/ SS 1.0 mm at full bend. All bed and structural components are annealed to remove manufacturing stress.<\/li>\n
    2. Cast-iron bed<\/strong> (B, B+, C, D, D+): CR 2.0 mm \/ SS 1.2 mm at full bend, with a correspondingly heavier structure.
      \nCommon working parameters across the series: bending angle 0\u2013180\u00b0, minimum bending height 5 mm, angle accuracy approximately \u00b10.5\u00b0\/m, straightness approximately 0.2 mm\/m, dimensional accuracy approximately \u00b10.1 mm\/m. Utilities are three-phase 380 V with a 0.6 MPa air supply.
      \nFor thick-plate work inside the sheet range, the W axis can be given a dedicated motor, or the W\/X\/Z axes upgraded to a three-motor drive with a thickened body. Auxiliary blades \u2014 upper, lower or both \u2014 can be specified and cut to length for localised short bends on a part. Where a workpiece needs to be lifted during forming, a C-axis lifting configuration and customised clamping are defined before build, not after.<\/li>\n<\/ol>\n

      Common working parameters across the series: bending angle 0\u2013180\u00b0, minimum bending height 5 mm, angle accuracy approximately \u00b10.5\u00b0\/m, straightness approximately 0.2 mm\/m, dimensional accuracy approximately \u00b10.1 mm\/m. Utilities are three-phase 380 V with a 0.6 MPa air supply.
      \nFor thick-plate work inside the sheet range, the W axis can be given a dedicated motor, or the W\/X\/Z axes upgraded to a three-motor drive with a thickened body. Auxiliary blades \u2014 upper, lower or both \u2014 can be specified and cut to length for localised short bends on a part. Where a workpiece needs to be lifted during forming, a C-axis lifting configuration and customised clamping are defined before build, not after.
      \nDead edges, arcs and offsets sit slightly outside this family. Those belong on the flexible edge bending machine, which forms to a 100 mm maximum bend height with a 4 mm minimum, in 1200, 1600 and 2000 sizes.<\/p>\n

      \"S\u00e9rie<\/p>\n

      Safety and compliance are not the same conversation<\/h2>\n

      This is the part that surprises European and Middle Eastern buyers late in a project.
      \nA press brake is an open-tool machine with a moving beam and an operator’s hands near the die line. Under the EU Machinery Directive 2006\/42\/EC, presence-sensing protection and safe control architecture are not optional extras. EN 12622 covers hydraulic press brake safety specifically, EN ISO 16092 the wider press family, and EN ISO 13849-1 the performance level required of the safety control system. STON<\/a>‘s press brakes ship with a laser protection device that stops the beam when the monitored zone is broken.
      \nA panel bender is a different risk profile: the forming zone is enclosed, and the operator’s role is loading and unloading rather than positioning during the stroke. Guarding is fencing and interlocks rather than presence sensing at the tool line. It does not remove the CE obligation, but it changes what the risk assessment under EN ISO 12100 concludes, and it usually changes the insurance and operator-training picture too.
      \nAsk any supplier which of these standards their declaration of conformity references. A vague “CE certified” answer is worth following up on.<\/p>\n

      FAQ:<\/h2>\n

      Q: Can a panel bender fully replace our press brakes?<\/p>\n

      A: Not in any plant we have configured. It replaces the repeating enclosure volume. Prototypes, thick brackets, oversized single bends and last-minute remakes stay on the press brake. Plan the panel bender as the machine that unloads your press brakes, not as the one that retires them.<\/p>\n

      Q: What thickness can a panel bender actually handle?<\/p>\n

      A: On STON<\/a>‘s press-arm series, 1.5 mm cold-rolled and 1.0 mm stainless with a welded bed, or 2.0 mm and 1.2 mm with a cast-iron bed, at full bend. Aluminium runs slightly higher. If your parts sit right at these numbers, request a forming trial on your own material rather than relying on the table, because temper and coating both affect the result.<\/p>\n

      Q: We make electrical cabinets. Which machine first?<\/p>\n

      A: Usually the panel bender, provided your doors and side panels stay within the thickness limits and above the 140 \u00d7 190 mm minimum. Cabinet work is the archetypal case: many short flanges, four sides, high repeat, and a surface finish that suffers from repeated manual handling.<\/p>\n

      Q: How much floor space does each need?<\/p>\n

      A: A press brake occupies less machine footprint but needs handling and staging space around it, plus room for a second operator on long parts. A panel bender occupies more of a fixed cell and less variable space. Compare total cell area, not machine dimensions on the drawing.<\/p>\n

      Q: What does either machine cost?<\/p>\n

      A: STON does not publish list prices for panel benders or press brakes, because both are configured per application \u2014 bed type, blade height, axis upgrades, tooling, automation interface. Request a quotation against your part drawings. Any supplier giving you a firm figure before seeing your geometry is quoting a catalogue machine, not your machine.<\/p>\n

      Q: Can we add automatic loading later?<\/p>\n

      A: Yes on both families. STON’s panel benders and press brakes retain a native loading and unloading interface compatible with most robot arms and gantry systems. Retrofitting is far easier when the interface exists from day one, so specify it at purchase even if you install the robot two years later.<\/p>\n

      Q: Which is easier to staff?<\/p>\n

      A: The panel bender, decisively. Press brake accuracy tracks operator experience, and experienced brake operators are hard to hire in most markets. A panel bender moves that skill into the program.<\/p>\n

       <\/p>","protected":false},"excerpt":{"rendered":"

      Choose a panel bender when one part carries many short flanges and the sheet stays inside the machine’s thickness range: on STON‘s press-arm series that means cold-rolled steel up to 2.0 mm and stainless up to 1.2 mm on a cast-iron bed. Choose a press brake when thickness, tonnage or unpredictable geometry drives the job. […]<\/p>\n","protected":false},"featured_media":0,"comment_status":"open","ping_status":"closed","template":"","class_list":["post-7891","news","type-news","status-publish","hentry","news_category-industry-news"],"acf":[],"_links":{"self":[{"href":"https:\/\/stoncncmachine.com\/fr\/wp-json\/wp\/v2\/news\/7891","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/stoncncmachine.com\/fr\/wp-json\/wp\/v2\/news"}],"about":[{"href":"https:\/\/stoncncmachine.com\/fr\/wp-json\/wp\/v2\/types\/news"}],"replies":[{"embeddable":true,"href":"https:\/\/stoncncmachine.com\/fr\/wp-json\/wp\/v2\/comments?post=7891"}],"wp:attachment":[{"href":"https:\/\/stoncncmachine.com\/fr\/wp-json\/wp\/v2\/media?parent=7891"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}